AdVantage Pro Freeze Dryer / Lyophilizer with Intellitronics Controller

The AdVantage Pro freeze dryer with Intellitronics™ Controller now offers users the benefit of Ethernet communication and email options. Monitor your cycle from anywhere you receive email! Get the convenience of a tray dryer in a benchtop unit.

 

Features:

  • Convenience of a tray dryer in a benchtop unit.
  • Intellitronics™ controller with a full-color, touch-screen display.
  • Available with up to three (3) usable product drying shelves.
  • Optional pneumatic stoppering system available to stopper vials.
  • Six-liter ice condensing capacity.

  Access Intellitronics™ Controller Simulation

View F-Gas Range for this product.

    Click the image to zoom in

    • Advantage Pro Lyophilizer

      Advantage Pro Lyophilizer

    • Advantage Pro Lyophilizer

      Advantage Pro Lyophilizer

    • Intellitronics Touch Screen Controller

      Intellitronics Touch Screen Controller

    • Advantage Pro_Removable Trays

      Advantage Pro_Removable Trays

    • ADV Pro_Removable Trays

      ADV Pro_Removable Trays

    • ADV Pro with Flask

      ADV Pro with Flask

    • ADV Pro with Thermocouples

      ADV Pro with Thermocouples

    Get More Information

    Key Features & Benefits

    • Intellitronics™ controller with a full-color, touch-screen display.  
    • Available with up to three (3) usable product drying shelves.
    • Optional pneumatic stoppering system available to stopper vials.
    • Six-liter ice condensing capacity.
    • Alarms alerts received via e-mail.
    • Ethernet enabled communications.
    • Integrated performance and leak tests.
    • Recipe customization (up to 10 Thermal Treatment and 12 Drying steps).
    • Remote access available via Remote Operator and SD Card Suite software.
    • 4 product probes 

     

     

    Performance Specifications

     

    XL

    EL

    Shelf Temperature Control Range*

    -40 to 60 °C

    -55 to 60 °C

    Lowest Shelf Temperature

    -57 °C @ 50 Hz
    -60 °C @ 60 Hz

    -62 °C @ 50 Hz
    -65 °C @ 60 Hz

    Shelf Pull-Down from
    20 °C to -40 °C

    ≤ 40 minutes

    ≤ 30 minutes

    Temperature Uniformity

    ± 1.0 °C

    ± 1.0 °C

    Lowest Condenser Temperature

    -67 °C @ 50 Hz
    -70 °C @ 60 Hz

    -82 °C @ 50 Hz
    -85 °C @ 60 Hz

    Maximum Condenser Capacity

    6 L

    6 L

    Maximum Ice Condensing
    Capacity in 24 hours
    \\

    4 L

    4 L

    Maximum Deposition Rate\\

    0.17 L/hour

    0.17 L/hour

    Vacuum Rate of Rise

    ≤ 60 mT/hour
    (≤ .08 mbar/hour)

    ≤ 60 mT/hour
    (≤ .08 mbar/hour)

    Number of Compressors

    1

    2

    Compressor Horsepower

    3/4

    1/3, 3/4

    System Refrigerant

    R245fa, R508B

    R508B, R407C

    Note: Performance specifications are based on SP Scientific test data from units operating at an ambient room temperature of approximately 20 °C. SP Scientific recommends an operating range of 15-25 °C (59-77 °F).

     

    Utility Requirements

     

    XL

    EL

    Compressed Air
    (Stoppering Option Only)

    60 - 90 psig
    (4.1 - 6.2 bar)

    60 - 90 psig
    (4.1 - 6.2 bar)

    Approx. Peak Heat Generated
    (With Vacuum Pump)

    5,000 BTU/h (1.5 kW)

    7,000 BTU/h (2 kW)

    Approx. Peak Heat Generated
    (Without Vacuum Pump)

    4,000 BTU/h (1.2 kW)

    6,000 BTU/h (1.8 kW)

    Electrical Requirements**

     

    XL

    EL

     

    Voltage

    208 / 230 VAC

    208 / 230 VAC

     

    Hertz

    50 Hz, 60 Hz

    50 Hz, 60 Hz

     

    Breaker Amperage
    (Type C or D)

    10 A

    15 A

     

    Phase

    1 Φ

    1 Φ

     

     

    * Shelf temperature is controlled to within ± 0.5 °C of the setpoint within the Shelf Temperature Control Range. 

    The Lowest Shelf Temperature and Lowest Condenser Temperature values may be lower than or equal to the Performance Specifications. 

    Shelf pull-down times are based on tests performed with no load at “pre-seal” pressure (approximately 400-500 mbar). The increased mass of stainless steel and additional heat transfer fluid for units with more than one shelf will increase the pull-down time. Use the following multipliers when determining the pull-down timespecification for the following shelf configurations:

    • 2-shelf units, standard pull-down time x 1.5 
    •  3-shelf units, standard pull-down time x 2.0

    Shelf temperature deviations shall not exceed the specification relative to the mean of the highest and lowest temperature readings. 

    \\ The specified Maximum Ice Condensing Capacity in 24 Hours and the Maximum Deposition Rate are based on the process of freeze-drying water as aggressively as possible.  The freeze dryer's ability to collect ice at an hourly rate or over a specified period will always be application dependent.  

     ** The AdVantage Pro is configured with an IEC60320 C20 inlet on the back of the unit. This inlet allows country specific power leads to be supplied. 

     †† The Advantage Pro is configured with a 1/4-inch BSPT bulkhead fitting. A BSPT to 1/4-inch NPT adapter shall be provided with the unit, which will allow users to choose between a  1/4-inch BSPT fitting and a 1/4-inch NPT fitting.

     

     

    • Laboratory research and development and/or small production freeze drying
    • Diagnostic kits
    • 96 well plates
    • Serum bottles and vials
    • Bulk products for analysis – plant material, organic tissue, waste products
    • Ethernet Access 
    • Remote Access Standard, but Configurable/Enabled by Customer
    • Stoppering
    • Side Manifold
    • Shelf Configuration
    • Latching Kit